Keysight E4356A Скачать руководство пользователя

Страница: 17 / 134

General Information

Output Characteristic

The power supply can operate in either CV (constant voltage) or CC (constant current) over its output voltage and current

ratings (see Figure 1-l). Although the power supply can operate in either mode, it is designed as a constant voltage source.

This means that the unit turns on in constant voltage mode with the output voltage rising to its Vset value. There is no

command for constant current operation. The only way to turn the unit on in constant current mode is by placing a short

across the output and then enabling or turning the output on.

Note that the power supply cannot be programmed to operate in a specific mode. After initial turn-on, the operating mode of

the unit will be determined by the voltage setting (V

), the current setting (I

), and the load impedance (RL). In Figure 1-1,

operating point 1 is defined by the load line cutting the operating locus in the constant-voltage region. This region defines

the CV mode. Operating point 2 is defined by the load line cutting the operating locus in the constant-current region. This

region defines the CC mode.

Appendix A lists the specifications and supplemental characteristics.

80V

70V

26A 30A

Vout

Iout

RL2

RL1

Figure 1-1. Output Characteristic Curve

Output Ranges

Figure 1-1 shows two output ranges: 80V, 26A and 70V, 30A. The step in the output characteristic indicates that the power

supply cannot simultaneously output 80V and 30A. No separate command is required to select a range, the power supply

automatically selects one of the operating ranges based on the

last

parameter (either voltage or current) that is programmed.

For example, if you program 80V and 30A, the power supply will select the 70V, 30A range based on the last parameter

that was programmed: 30A.

Downprogramming

The power supply can sink current for more rapid down programming in the CV mode. This is an uncharacterized current-

sinking area that provides a limited downprogramming capability.

Содержание E4356A







































































































































Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды

Keysight E4356A, Руководство по эксплуатации

Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды