Keysight E4356A Скачать руководство пользователя

Страница: 41 / 134

40 Front Panel Operation

Programming The Output

Important

These instructions show how to program a single power supply. There are special considerations when

you have two or more supplies connected in series or in autoparallel. See "Chapter 4 - User Connections

and Considerations".

The power supply accepts values directly in volts and amperes. Values will be rounded off to the nearest multiple of the

output resolution (see “Programming Resolution" in Table A-2). If you attempt to enter a value not in a valid range, the unit

will either switch to the other range or the entry will be ignored and

OUT OF RANGE

appears on the display.

Figure 1-1 shows the general response of the E4356A power supply. Unless directed otherwise, always keep the output

voltage and current within the boundaries of its operating line for the specified mode of operation (CV or CC).

Establishing Initial Conditions

Set the power supply to its *RST state by pressing

. This state was stored in location 0 at the factory. If it

has since been changed, you can restore it as directed under “Turn-on Conditions”, later in this chapter. *RST results in the

following operating conditions:



Zero voltage output.



Minimal current output.



Output disabled (

Dis

annunciator on).



Overcurrent protection off (

OCP

annunciator off).



Protection circuits cleared (

Prot

annunciator off).



Overvoltage protection set to maximum.

Programming Voltage

To program the output for 45 volts, proceed as follows:



Press

. The display will change from meter mode to indicate

VOLTS



Press

. If you discover a mistake before pressing

, erase the incorrect value with the

key.



The display will return to the meter mode and indicate 0.000 volts.



Press

to enable the output (

Dis

annunciator turns off). The

VOLTS

display will indicate 45.00 volts.

Note

The power supply must be programmed for a minimal current in order to increase the output voltage

beyond zero. Normally, there is sufficient idle current to do this. If the power supply does not respond or

the

annunciator turns on, go to “Programming Current” and set the current to a small value.



Now raise the voltage by pressing

.Note that the voltage increases by a specific increment (depending on the

voltage programming resolution) each time you press the key and increases rapidly as you hold down the key. To lower

the voltage, press



Try raising and lowering the voltage by rotating the

Voltage

control clockwise and then counterclockwise. Note how

the output responds as compared to using the

Entry

keys.



Try to program a voltage greater than the V

MAX

for your unit (see Table A-2). Note that the display shows

OUT OF

RANGE

Programming Overvoltage Protection

Overvoltage protection guards the load against voltages that reach a specified value above the programmed output voltage.

Содержание E4356A







































































































































Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды

Keysight E4356A, Руководство по эксплуатации

Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды