Keysight E4356A Скачать руководство пользователя

Страница: 123 / 134

122 Compatibility Language

Table G-1. ARPS Commands (continued)

ARPS Command

Description

Similar SCPI

Command

UNMASK?

This command reads which bits in the status register have been

enabled as fault conditions. The decimal equivalent of the total bit

weight of all enabled bits is returned.

STAT:OPER:ENAB?
STAT:QUES:ENAB?
ESE

FAULT?

This command reads which bits have been set in the fault register.

A bit is set in the fault register when the corresponding bit in the

status register changes from inactive to active AND the

corresponding bit in the mask register has been enabled. The fault

it has been read. The decimal equivalent

of the total bit weight of all enabled bits is returned.

STAT:OPER?
STAT:QUES?
*ESE

SRQ OFF
SRQ 0
SR*Q ON
SRQ 1

These commands enable or disable the power supply's ability to

request service from the controller for fault conditions.

UNMASK

defines which conditions are defined as faults.

Initial condition:

SRQ OFF

*SRE

SRQ?

This command reads the SRQ setting.

*SRE?

CLR

This command initializes the power supply to the power-on state.

It also resets the PON bit in the serial poll register. The command

performs the same function as the Device Clear (DCL) interface

message.

*RST

ERR?

This command determines the type of programming error detected

by the unit. A remote programming error sets the ERR bit in the

status register, which can be enabled by

UNMASK

to request

service.

SYST:ERR?

TEST?

This command causes the power supply to run selftest and report

any detected failures.

*TST?

ID?

This command causes the power supply to report its model number

and any options that affect the unit's output.

*IDN?

SYST:LANG

This command causes the alternate language to become active and

to be stored in nonvolatile memory. In this case, the commands are

equivalent. After being shut off, the power supply will resume in

the last-selected language when power is restored. The parameter

must be either

COMP

TMSL

not

SCPI

SYST:LANG

Содержание E4356A







































































































































Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды

Keysight E4356A, Руководство по эксплуатации

Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды