Keysight E4356A Скачать руководство пользователя

Страница: 5 / 134

Safety Symbol - Definitions

Symbol

Description

Symbol

Description

Direct current

Terminal for Line conductor on permanently installed

equipment

Alternating current

Caution, risk of electric shock

Both direct and alternating current

Caution, hot surface

Three-phase alternating current

Caution (refer to accompanying documents)

Earth (ground) terminal

In position of a bi-stable push control

Protective earth (ground) terminal

Out position of a bi-stable push control

Frame or chassis terminal

On (unit)

Terminal for Neutral conductor on

permanently installed equipment

Off (unit)

Terminal is at earth potential

(Used for measurement and control

circuits designed to be operated with one

terminal at earth potential.)

Standby (unit)

Units with this symbol are not completely disconnected

from ac mains when this switch is off. To completely

disconnect the unit from ac mains, either disconnect the

power cord or have a qualified electrician install an

external switch.

The WARNING sign denotes a hazard. It

calls attention to a procedure, practice, or

the like, which, if not correctly performed

or adhered to, could result in personal

injury. Do not proceed beyond a

WARNING sign until the indicated

conditions are fully understood and met.

The CAUTION sign denotes a hazard. It calls attention to

an operating procedure, or the like, which, if not correctly

performed or adhered to, could result in damage to or

destruction of part or all of the product. Do not proceed

beyond a CAUTION sign until the indicated conditions

are fully understood and met.

Acoustic Noise Information

Herstellerbescheinigung

Diese Information steht im Zusammenhang mit den Anforderungen der Maschinenläminformationsverordnung vom 18

Januar 1991. * Schalldruckpegel Lp <70 dB(A) * Am Arbeitsplatz * Normaler Betrieb * Nach EN 27779 (Typprufung).

Manufacturer's Declaration

This statement is provided to comply with the requirements of the German Sound Emission Directive, from 18 January

1991. * Sound Pressure Lp <70 dB(A) *At Operator Position * Normal Operation * According to EN 27779 (Type Test).

Printing History

The edition and current revision of this manual are indicated below. Reprints of this manual containing minor corrections

and updates may have the same printing date. Revised editions are identified by a new printing date. A revised edition

incorporates all new or corrected material since the previous printing date. Changes to the manual occurring between

revisions are covered by change sheets shipped with the manual. In some cases, the changes apply to specific instruments.

Instructions provided on the change sheet will indicate if a particular change applies only to certain instruments.



Edition 1 - August, 1999

Updated: March, 2000; Sept. 2004

Edition 2 - January 2015

This document contains proprietary information protected by copyright. All rights are reserved. No part of this document

may be photocopied, reproduced, or translated into another language without the prior consent of Keysight Technologies

Company. The information contained in this document is subject to change without notice.

Содержание E4356A







































































































































Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды

Keysight E4356A, Руководство по эксплуатации

Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды