Keysight E4356A Скачать руководство пользователя

Страница: 121 / 134

120 Compatibility Language

Table G-1. ARPS Commands

ARPS Command

Description

Similar SCPI

Command

VSET x
VSET xV
VSET xMV

These commands program output voltage. See Table 7-1 for the

programming ranges of these commands.

Initial condition: 0 V

VOLT

ISET x
ISET xA
ISET xMA

These commands program output current. See Table 7-1 for the

programming ranges for these commands.

Initial condition: 0 A

CURR

VSET?
ISET?

These commands read voltage or current settings.

VOLT?

CURR?

VOLT?
IOUT?

These commands measure and read output voltage or current.

MEAS:VOLT?

MEAS:CURR?

OVP x

OVP xV
OVP xMV

NOTE: OVP commands do not work with Keysight 603xA
supplies.

These commands program the overvoltage protection.

The OVP setting is programmed in either volts or millivolts. See

Table 7-1 for the programming ranges of these commands.

Initial condition: 10% above rated output.

VOLT:PROT

OVP?

This command reads the OVP setting.

VOLT:PROT?

VMAX x
VMAX xV
VMAX
xMV

These commands program an upper limit (soft limit) to the voltage

programming value that the power supply will accept. The

programming ranges are the same as those used for VSET.

(None)

IMAX x
IMAX xA
IMAX
xMA

These commands program an upper limit (soft limit) to the current

programming value that the power supply will accept. The

programming ranges are the same as those used for

ISET.

(None)

VMAX?
IMAX?

These commands read the soft voltage or current limits.

(None)

DLY x
DLY xS
DLY xMS

These commands program the delay time before a new output

voltage or current is implemented or an

RST, OUT ON,

CLR

command is received. During the delay the CV, CC, and CR

conditions cannot be reported as faults, and foldback protection is

disabled.

OUTP:PROT:DEL

DLY?

This command reads the delay time setting.

OUTP:PROT:DEL?

OUT OFF
OUT 0
OUT ON
OUT 1

These commands enable or disable the power supply output. The

disabled state programs the output to relatively low voltage and

current values. The unit will be able to implement commands even

while the output is disabled.

Initial condition:

OUT ON

OUTP:STAT OFF

OUTP:STAT 0

OUTP:STAT ON

OUTP:STAT 1

FOLD OFF
FOLD

FOLD 2
FOLD

FOLD CV
FOLD 1
FOLD CC
FOLD 2

These commands enable or disable Foldback protection.

Foldback protection disables the power supply output if the power

supply switches to whichever mode (CV or CC) is defined as the

fold (error) condition. Note that foldback protection is disabled

during the DELAY period.

Initial condition:

FOLD OFF

(None)

FOLD?

This command reads the Foldback setting.

(None)

x =

any digit (within range)

MA =

milliampere

MV =

millivolt

MS =

millisecond.

Содержание E4356A







































































































































Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды

Keysight E4356A, Руководство по эксплуатации

Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды