Keysight E4356A Скачать руководство пользователя

Страница: 49 / 134

48 Remote Programming

The optional header

SOURCE

precedes the current, digital, and voltage subsystems. This effectively makes

CURRENT,

:DIGITAL,

and

VOLTAGE

root-level commands.

Moving Among Subsystems

In order to combine commands from different subsystems, you need to be able to restore the active path to the root. You do

this with the root specifier (:). For example, you could clear the output protection and check the status of the Operation

Condition register as follows :

OUTPUT:PROTECTION:CLEAR

STATUS:OPERATION:CONDITION?

By using the root specifier, you could do the same thing in one message:

OUTPUT:PROTECTION:CLEAR;:STATUS:OPERATION:CONDITION?

Note

The SCPI parser traverses the command tree as described in Appendix A of the IEEE 488.2 standard. The

"Enhanced Tree Walking Implementation" given in that appendix is

not

implemented in the power supply.

The following message shows how to combine commands from different subsystems as well as within the same subsystem:

VOLTAGE:LEVEL 7;PROTECTION 8;:CURRENT:LEVEL I50;PROTECTION ON

Note the use of the optional header

LEVEL

to maintain the correct path within the voltage and current subsystems and the

use of the root specifier to move between subsytems.

Including Common Commands

You can combine common commands with system commands in the same message. Treat the common command as a

message unit by separating it with the message unit separator. Common commands

do not affect the active header path;

you may insert them anywhere in the message.

VOLT:TRIG 7.5;INIT;*TRG
OUTP OFF;*RCL 2;OUTP ON

SCPI Queries

Observe the following precautions with queries:



Remember to set up the proper number of variables for the returned data.



Set the program to read back all the results of a query before sending another command to the power supply.

Otherwise, a

Query Interrupted

error will occur and the unreturned data will be lost.

Value Coupling

Value coupling results when a command directed to send one parameter also changes the value of a second parameter.

There is no direct coupling among any power supply SCPI commands. However, be aware

that until they are programmed,

unititialized trigger levels will assume their corresponding immediate levels. For example, if a power supply is powered up

and

VOLT:LEV

is programmed to

then

VOLT:LEV:TRIG

will also be

until you program it to another value. Once

you program

VOLT:LEV:TRIG

to another value, it will remain at that value regardless of how you subsequently

reprogram

VOLT:LEVEL.

Содержание E4356A







































































































































Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды

Keysight E4356A, Руководство по эксплуатации

Результаты поиска

Содержание E4356A

Отзывы:

Похожие инструкции для E4356A

Бренды по названию

Популярные бренды