JDS Uniphase CellAdvisor JD780A Series Скачать руководство пользователя страница 429 | Manualshive

Страница: 429 / 592

JDS Uniphase CellAdvisor JD780A Series Скачать руководство пользователя страница 429

JD780A Series Analyzers

Using TD-SCDMA Signal Analyzer

429

Procedure

1.

Press the

LIMIT

hot key.

2.

Press the

RF Test Limits

soft key.

3.

Select the test item(s) and set the limit(s) depending on your selected measurement mode:

To set the limit for

Select

Set

Channel power

Channel Power

High Limit
Low Limit

Occupied bandwidth

Occupied BW

High Limit

Spectrum emission mask

Spectrum Emission Mask

(On/Off only)

ACLR

ACLR

(On/Off only)

Multi-ACLR

Multi-ACLR

(On/Off only)

Spurious emissions

Spurious Emissions

(On/Off only)

4.

Optional

. You can enable alarm sound that goes off if the measurement falls outside of the limit.

Toggle the

Beep

soft key between

On

and

Off

to enable or disable the beep sound.

5.

Optional

. Go to

SAVE/LOAD

> Save

, and then select

Limit

to save the limit settings.

See

“Using save” on page 31 for more information.

Conducting power vs. time measurements

The Power vs. Time (P vs T) measurement analyzes the amplitude profile and timing of the burst
signal and provides a time mask for the signal. It measures the mean transmit power during the “useful
part” of TD-SCDMA bursts and verifies that the power ramp fits within the defined mask. TD-SCDMA is
a Time Division Multiple Access (TDMA) scheme with seven time slots, or bursts, per RF channel and
by using the “Multi-Slot” function, up to seven slots in a frame can be viewed at one time.

Power vs. time (slot)

The Power vs. Time (Slot) in TD-SCDMA Signal Analyzer measures the modulation envelope in the
time domain, showing the signal rise and fall shape of TD-SCDMA signal.

Setting measure setup

After configuring test parameters as described in the

“Configuring test parameters” on page 415, you

can continue your measurement. The measurement settings can be saved and recalled as a file.

Procedure

1.

Press the

MEASURE SETUP

hot key.

2.

Press the

Slot Number

soft key, and then select the time slot number to be displayed:

TS0

,

TS1

,

TS2

,

TS3

,

TS4

,

TS5

, or

TS6

.

3.

Press the

Spread Factor

soft key, and then select the spread factor option:

DL Auto

for auto

detection of downlink,

UL Auto

for auto detection of uplink,

SF1

,

SF2

,

SF4

,

SF8

, or

SF16

4.

To set the number of maximum users, complete the following steps:

a.

Press the

Max Users

soft key.

«
...
427
428
429
430
431
...
»

Содержание CellAdvisor JD780A Series

















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды