JDS Uniphase CellAdvisor JD780A Series Скачать руководство пользователя страница 137 | Manualshive

Страница: 137 / 592

JDS Uniphase CellAdvisor JD780A Series Скачать руководство пользователя страница 137

JD780A Series Analyzers

Using GSM/GPRS/EDGE Signal Analyzer

137

Conducting power vs. time measurements

The Power vs. Time measurement measures the mean transmission power during the useful part of
GSM bursts and verifies that the power ramp fits within the defined mask. It also lets you view the rise,
fall, and useful part of the GSM burst.

This measurement provides masks for both of Base Transceiver Station (BTS) and Mobile Station
(MS). The timing masks are referenced to the transition from the bit 13 to the bit 14 of the mid-amble
training sequence. For GMSK measurements, the 0 dB reference is determined by measuring the
mean transmitted power during the useful part of the burst.

Power vs. time (slot)

Setting measure setup

After configuring test parameters as described in the

“Configuring test parameters” on page 125, you

can continue your measurement. The measurement settings can be saved and recalled as a file.

Procedure

1.

Press the

MEASURE SETUP

hot key.

2.

Press the

Time Slot

soft key to assign a time slot with which performs measurements, and then

select your desired time slot number from

0

to

7

.

3.

Press the

Detect Mode

soft key, and then select the signal standard option:

Auto

,

GSM

, or

EDGE

. Auto is set by default. The instrument applies a mask automatically based on the selected

mode.

4.

Optional

. To set the delay, complete the following steps:

a.

Press the

Miscellaneous

soft key.

b.

Press the

Delay

soft key to set the amount of delay in µs.

c.

Enter a value by using the numeric keys. You can also use the rotary knob.

d.

Press the

µs

soft key.

NOTE

The Delay setting is used only when there is a time offset in the signals to be measured.

Setting limit for burst power

Procedure

1.

Press the

LIMIT

hot key.

2.

Press the

PvsT Test Limits

soft key.

3.

Press the

Burst Power

soft key to set the limit in the Power vs. Time (Slot) measurement.

4.

Toggle the

Test Limits

soft key between

On

and

Off

to enable or disable the Pass/Fail

indication.

5.

Set the upper threshold:

a.

Press the

High Limit

soft key.

b.

Enter a value for the upper limit, and then press the

dBm

unit soft key.

6.

Set the lower threshold:

a.

Press the

Low Limit

soft key.

«
...
135
136
137
138
139
...
»

Содержание CellAdvisor JD780A Series

















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды