JDS Uniphase CellAdvisor JD780A Series Скачать руководство пользователя страница 202

Страница: 202 / 592

JD780A Series Analyzers

202

Using LTE - FDD Signal Analyzer

Procedure

Connect an external reference or a GPS antenna to the JD780A series.

Press the

SYSTEM

hot key.

Press the

Freq Reference

soft key, and then select the reference option:

Internal

External 10

MHz

External 13 MHz

External 15 MHz

, or

GPS

Table 14

External reference indicators

Type

Indicator

Description

Internal

(green)

The green

INT

icon indicates that the instrument uses the built-in

internal time base.

External

(green)

The green

EXT

icon indicates that an external reference is connected

and locked and that the instrument uses the same reference clock as
the signal source.

External

(red)

The red

EXT

icon indicates that an external reference is connect but not

locked.

GPS

(green)

The green GPS antenna icon indicates that a GPS antenna is
connected and locked.

GPS

(yellow)

The yellow GPS antenna icon indicates that a GPS antenna is
connected and locking is in progress.

GPS

(grey)

The grey GPS antenna icon indicates that a GPS antenna is not
connected, failed, or unable to be locked.

Conducting spectrum measurements

Setting measure setup

After configuring test parameters as described in the

“Configuring test parameters” on page 197, you

can continue your measurement.

Procedure

Press the

MEASURE SETUP

hot key.

Press the

Bandwidth

soft key.

Select the nominal channel bandwidth to be measured, from the following choices:

–

1.4 MHz

3 MHz

5 MHz

10 MHz

15 MHz

, and

20 MHz

Your measurement result is displayed on the screen as like the following example, Figure 82.

Содержание CellAdvisor JD780A Series

















































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание CellAdvisor JD780A Series

Отзывы:

Бренды по названию

Популярные бренды

JDS Uniphase CellAdvisor JD780A Series, Руководство пользователя

Результаты поиска

Содержание CellAdvisor JD780A Series

Отзывы:

Бренды по названию

Популярные бренды