INVT GD200L-004G-4 Скачать руководство пользователя страница 69

Страница: 69 / 187

Goodrive200L

inverters Function parameters

Function

code

Name

Detailed instruction of parameters

Default

value

Modify

P07.02

QUICK/JOG

function

selection

0:No function

1: Jogging. Press QUICK/JOG to begin the

jogging running.

2: Shift the display state by the shifting key.

Press QUICK/JOGto shift the displayed function

code from right to left.

3: Shift between forward rotations and reverse

rotations. Press QUICK/JOG to shift the direction

of the frequency commands. This function is only

valid in the keypad commands channels.

4: Clear UP/DOWN settings. Press QUICK/JOG

to clear the set value of UP/DOWN.

5: Coast to stop. Press QUICK/JOG to coast to

stop.

6: Shift the running commands source. Press

QUICK/JOG to shift the running commands

source.

7:Quick commission mode(committee according

to the non-factory parameter)

Note:

Press QUICK/JOGto shift between

forward rotation and reverse rotation, the inverter

does not record the state after shifting during

powering off. The inverter will run according to

parameter P00.13 during next powering on.

◎

P07.03

Shifting

sequence

selection of

QUICK/JOG

commands

When P07.02=6, set the shifting sequence of

running command channels.

0:Keypad control→terminals control

→communication control

1:Keypad control←→terminals control

2:Keypad control←→communication control

3:Terminals control←→communication control

○

P07.04

STOP/RST

stop function

STOP/RST is valid for stop function. STOP/RST

is valid in any state for the fault reset.

0:Only valid for the keypad control

1:Both valid for keypad and terminals control

2:Both valid for keypad and communication

control

3:Valid for all control modes

○

P07.05

Parameters

state 1

0x0000~0xFFFF

BIT0:running frequency (Hz on)

BIT1:set frequency(Hz flickering)

0x03FF

○

Содержание GD200L-004G-4




























































































































































































Результаты поиска

Содержание GD200L-004G-4

Отзывы:

Бренды по названию

Популярные бренды

INVT GD200L-004G-4, Руководство по эксплуатации

Результаты поиска

Содержание GD200L-004G-4

Отзывы:

Бренды по названию

Популярные бренды