INVT GD200L-004G-4 Скачать руководство пользователя страница 6

Страница: 6 / 187

Goodrive200L

inverters Safety precautions

Safety Precautions 1

1.1 What this chapter contains

Please read this manual carefully and follow all safety precautions before moving, installing,

operating and servicing the inverter. If ignored, physical injury or death may occur, or

damage may occur to the devices.

If any physical injury or death or damage to the devices occurs for ignoring to the safety

precautions in the manual, our company will not be responsible for any damages and we are

not legally bound in any manner.

1.2 Safety definition

Danger:

Serious physical injury or even death may occur if not follow

relevant requirements

Warning:

Physical injury or damage to the devices may occur if not follow

relevant requirements

Note:

Physical hurt may occur if not follow relevant requirements

Qualified

electricians:

People working on the device should take part in professional

electrical and safety training, receive the certification and be

familiar

with

all

steps

and

requirements

installing,

commissioning, operating and maintaining the device to avoid any

emergency.

1.3 Warning symbols

Warnings caution you about conditions which can result in serious injury or death and/or

damage to the equipment, and advice on how to avoid the danger. Following warning

symbols are used in this manual:

Symbols

Name

Instruction

Abbreviation

Danger

Electrical

Danger

Serious physical injury or even

death may occur if not follow the

relative requirements

Warning

General

danger

Physical injury or damage to the

devices may occur if not follow the

relative requirements

Do not

Electrostatic

discharge

Damage to the PCBA board may

occur if not follow the relative

requirements

Hot sides

Sides of the device may become

hot. Do not touch.

Note

Physical hurt may occur if not follow

the relative requirements

Note

Содержание GD200L-004G-4




























































































































































































Результаты поиска

Содержание GD200L-004G-4

Отзывы:

Бренды по названию

Популярные бренды

INVT GD200L-004G-4, Руководство по эксплуатации

Результаты поиска

Содержание GD200L-004G-4

Отзывы:

Бренды по названию

Популярные бренды