manualshive.com logo in svg

IBM System x iDataPlex dx360 M4 7912, Руководство по обслуживанию

Поделиться
Скачать
IBM System x iDataPlex dx360 M4 7912 Скачать руководство пользователя страница 46

W.305800D

[W.305800D] DRIVER HEALTH
PROTOCOL: Disconnect Controller
Failed. Requires 'Reboot'.

Explanation:

DRIVER HEALTH PROTOCOL:

Disconnect Controller Failed. Requires 'Reboot'

Severity:

Warning

User response:

Complete the following steps:

1.

Reboot the system to reconnect the controller.

2.

If problem persists, switch to backup UEFI or

reflash current UEFI image.

3.

(Trained Service Technician Only) Replace system

board.

W.305800E

[W.305800E] DRIVER HEALTH
PROTOCOL: Reports Invalid Health
Status Driver.

Explanation:

DRIVER HEALTH PROTOCOL: Reports

Invalid Health Status Driver

Severity:

Warning

User response:

Complete the following steps:

1.

Reboot the system.

2.

If problem persists, switch to backup UEFI or

reflash current UEFI image.

3.

(Trained Service Technician Only) Replace system

board.

W.3808000

[W.3808000] An IMM communication
failure has occurred.

Explanation:

IMM Communication Failure

Severity:

Warning

User response:

Complete the following steps:

1.

Reset IMM.

2.

Remove AUX power from the system. This will

reboot the entire system.

3.

Check IBM support site for an applicable service

bulletin or firmware update that applies to this error.

4.

Reflash UEFI Firmware.

5.

(Trained service technician only) Replace the

system board.

W.3808002

[W.3808002] An error occurred while
saving UEFI settings to the IMM.

Explanation:

Error Updating System Configuration to

IMM

Severity:

Warning

User response:

Complete the following steps:

1.

Use F1 Setup, Verify Settings and Save Settings to

recover settings.

2.

Reset IMM.

3.

Remove AUX power from the system. This will

reboot the entire system.

4.

Check IBM support site for an applicable service

bulletin or firmware update that applies to this error.

5.

Reflash IMM Firmware.

6.

Remove and re-install CMOS battery for 30

seconds to clear CMOS contents.

7.

(Trained Service technician only) Replace the

system board.

W.3808003

.[W.3808003] Unable to retrieve the
system configuration from the IMM.

Explanation:

Error Retrieving System Configuration

from IMM

Severity:

Warning

User response:

Complete the following steps:

1.

Use F1 Setup, Verify Settings and Save Settings to

recover settings.

2.

Reset IMM.

3.

Remove AUX power from the system. This will

reboot the entire system.

4.

Check IBM support site for an applicable service

bulletin or firmware update that applies to this error.

5.

Reflash IMM Firmware.

6.

Remove and re-install CMOS battery for 30

seconds to clear CMOS contents.

7.

(Trained Service technician only) Replace the

system board.

W.3818005

[W.3818005] The CRTM flash driver
could not successfully flash the
staging area. The update was aborted

Explanation:

CRTM Update Aborted

Severity:

Warning

User response:

Complete the following steps:

1.

Continue booting system. If system does not reset,

manually reset the system.

2.

If the error is not reported on the subsequent boot,

no additional recovery action is required.

3.

If the event persists, continue booting system and

reflash UEFI image.

4.

(Trained service technician only) Replace the

system board.

W.381800D

[W.381800D] TPM physical presence is
in asserted state

Explanation:

TPM physical presence is in asserted

state

Severity:

Warning

User response:

Complete the following steps:

W.305800D • W.381800D

28

System x iDataPlex dx360 M4 Types 7912 and 7913: Problem Determination and Service Guide

Содержание System x iDataPlex dx360 M4 7912

















































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды