IBM System x iDataPlex dx360 M4 7912 Скачать руководство пользователя страница 212

Страница: 212 / 400

Serviceable:

Yes

Recoverable:

Automatically notify Support:

User response:

Complete the following steps:

1. Check component firmware level and upgrade if

necessary. The installed firmware level can be found
in the DSA Diagnostic Event Log within the
Firmware/VPD section for this component.

2. Rerun the test.

3. If failure remains, refer to "Troubleshooting by

symptom" in the system "Installation and Service
Guide" for the next corrective action.

Date Message Added:

08/31/2012

Reviewed:

08/31/2012

405-901-000 BRCM:TestMIIRegisters Test Failed

Explanation:

A failure was detected while testing

internal PHY registers.

Internal Event:

Severity:

Error

Serviceable:

Yes

Recoverable:

Automatically notify Support:

User response:

Complete the following steps:

1. Check component firmware level and upgrade if

necessary. The installed firmware level can be found
in the DSA Diagnostic Event Log within the
Firmware/VPD section for this component.

2. Rerun the test.

3. If failure remains, refer to "Troubleshooting by

symptom" in the system "Installation and Service
Guide" for the next corrective action.

Date Message Added:

08/31/2012

Reviewed:

08/31/2012

405-902-000 BRCM:TestEEPROM Test Failed

Explanation:

A failure was detected while testing

non-volatile RAM.

Internal Event:

Severity:

Error

Serviceable:

Yes

Recoverable:

Automatically notify Support:

User response:

Complete the following steps:

1. Check component firmware level and upgrade if

necessary. The installed firmware level can be found

in the DSA Diagnostic Event Log within the
Firmware/VPD section for this component.

2. Rerun the test.

3. If failure remains, refer to "Troubleshooting by

symptom" in the system "Installation and Service
Guide" for the next corrective action.

Date Message Added:

08/31/2012

Reviewed:

08/31/2012

405-903-000 BRCM:TestInternalMemory Test Failed

Explanation:

A failure was detected while testing

internal memory.

Internal Event:

Severity:

Error

Serviceable:

Yes

Recoverable:

Automatically notify Support:

User response:

Complete the following steps:

1. Check component firmware level and upgrade if

necessary. The installed firmware level can be found
in the DSA Diagnostic Event Log within the
Firmware/VPD section for this component.

2. Rerun the test.

3. If failure remains, refer to "Troubleshooting by

symptom" in the system "Installation and Service
Guide" for the next corrective action.

Date Message Added:

08/31/2012

Reviewed:

08/31/2012

405-904-000 BRCM:TestInterrupt Test Failed

Explanation:

A failure was detected while testing

interrupts.

Internal Event:

Severity:

Error

Serviceable:

Yes

Recoverable:

Automatically notify Support:

User response:

Complete the following steps:

1. Check component firmware level and upgrade if

necessary. The installed firmware level can be found
in the DSA Diagnostic Event Log within the
Firmware/VPD section for this component.

2. Rerun the test.

3. If failure remains, refer to "Troubleshooting by

symptom" in the system "Installation and Service
Guide" for the next corrective action.

Date Message Added:

08/31/2012

405-901-000 • 405-904-000

194

System x iDataPlex dx360 M4 Types 7912 and 7913: Problem Determination and Service Guide

Содержание System x iDataPlex dx360 M4 7912

















































































































































































































































































































































































































Результаты поиска

Содержание System x iDataPlex dx360 M4 7912

Отзывы:

Бренды по названию

Популярные бренды

IBM System x iDataPlex dx360 M4 7912, Руководство по обслуживанию

Результаты поиска

Содержание System x iDataPlex dx360 M4 7912

Отзывы:

Бренды по названию

Популярные бренды