IBM System x iDataPlex dx360 M4 7912 страница 213 Скачать руководство пользователя

Страница: 213 / 400

Reviewed:

08/31/2012

405-905-000 BRCM:TestLoopbackMAC Test Failed

Explanation:

BRCM:TestLoopbackMAC Test Failed.

Internal Event:

Severity:

Error

Serviceable:

Yes

Recoverable:

Automatically notify Support:

User response:

Complete the following steps:

1. Check component firmware level and upgrade if

necessary. The installed firmware level can be found
in the DSA Diagnostic Event Log within the
Firmware/VPD section for this component.

2. Rerun the test.

3. If failure remains, refer to "Troubleshooting by

symptom" in the system "Installation and Service
Guide" for the next corrective action.

Date Message Added:

08/31/2012

Reviewed:

08/31/2012

405-906-000 BRCM:TestLoopbackPhysical Test

Failed

Explanation:

A failure was detected during the

loopback test at the physical layer.

Internal Event:

Severity:

Error

Serviceable:

Yes

Recoverable:

Automatically notify Support:

User response:

Complete the following steps:

1. Check component firmware level and upgrade if

necessary. The installed firmware level can be found
in the DSA Diagnostic Event Log within the
Firmware/VPD section for this component.

2. Rerun the test.

3. If failure remains, refer to "Troubleshooting by

symptom" in the system "Installation and Service
Guide" for the next corrective action.

Date Message Added:

08/31/2012

Reviewed:

08/31/2012

405-907-000 BRCM:TestLEDs Test Failed

Explanation:

A failure was detected while verifying

operation of the status LEDs.

Internal Event:

Severity:

Error

Serviceable:

Yes

Recoverable:

Automatically notify Support:

User response:

Complete the following steps:

1. Check component firmware level and upgrade if

necessary. The installed firmware level can be found
in the DSA Diagnostic Event Log within the
Firmware/VPD section for this component.

2. Rerun the test.

3. If failure remains, refer to "Troubleshooting by

symptom" in the system "Installation and Service
Guide" for the next corrective action.

Date Message Added:

08/31/2012

Reviewed:

08/31/2012

218-000-000 Brocade:MemoryTest Passed

Explanation:

The test passed.

Internal Event:

Severity:

Event

Serviceable:

Recoverable:

Automatically notify Support:

Date Message Added:

09/03/2012

Reviewed:

09/03/2012

218-001-000 Brocade:ExternalLoopbackTest Passed

Explanation:

The test passed.

Internal Event:

Severity:

Event

Serviceable:

Recoverable:

Automatically notify Support:

Date Message Added:

09/03/2012

Reviewed:

09/03/2012

218-002-000 Brocade:SerdesLoopbackTest Passed

Explanation:

The test passed.

Internal Event:

Severity:

Event

Serviceable:

Recoverable:

Automatically notify Support:

405-905-000 • 218-002-000

Chapter 3. Diagnostics

195

Содержание System x iDataPlex dx360 M4 7912

















































































































































































































































































































































































































Результаты поиска

Содержание System x iDataPlex dx360 M4 7912

Отзывы:

Похожие инструкции для System x iDataPlex dx360 M4 7912

Бренды по названию

Популярные бренды

IBM System x iDataPlex dx360 M4 7912, Руководство по обслуживанию

Результаты поиска

Содержание System x iDataPlex dx360 M4 7912

Отзывы:

Похожие инструкции для System x iDataPlex dx360 M4 7912

Бренды по названию

Популярные бренды