IBM System x iDataPlex dx360 M4 7912 страница 48 Скачать руководство пользователя | Manualshive

Страница: 48 / 400

background image

User response:

Complete the following steps:

1.

If a DIMM connector error LED is lit, resolve the

failure.

2.

Make sure that the DIMM connectors are correctly

populated for mirroring mode, according to the
service information for this product.

W.580A2

[W.580A2] Invalid memory
configuration for Sparing Mode. Please
correct memory configuration.

Explanation:

Unsupported DIMM Population for Spare

Mode

Severity:

Error

User response:

Complete the following steps:

1.

Make sure that the DIMM connectors are correctly

populated for sparing mode, according to the service
information for this product.

W.68002

[W.68002] A CMOS battery error has
been detected

Explanation:

CMOS Battery Fault

Severity:

Error

User response:

Complete the following steps:

1.

If the system was recently Installed, Moved, or

Serviced, makesure the batter is properly seated.

2.

Check IBM support site for an applicable service

bulletin or firmware update that applies to this error.

3.

Replace CMOS Battery

4.

(Trained Service technician only) Replace the

system board.

System event log

The system event log contains messages of three types:

Information

Information messages do not require action; they record significant
system-level events, such as when the server is started.

Warning

Warning messages do not require immediate action; they indicate possible
problems, such as when the recommended maximum ambient temperature
is exceeded.

Error

Error messages might require action; they indicate system errors, such as
when a fan is not detected.

Each message contains date and time information, and it indicates the source of
the message (POST or the IMM2).

Integrated management module II (IMM2) error messages

The following table describes the IMM2 error messages and suggested actions to
correct the detected problems.

For more information about IMM2, see the

Integrated Management Module II User's

Guide

at http://www.ibm.com/support/entry/portal/docdisplay?lndocid=MIGR-

40000001-00000000

Management Controller [arg1]

Network Initialization Complete.

Explanation:

This message is for the use case where

a Management Controller network has completed
initialization.

Internal Event:

No

Severity:

Info

Alert Category:

System - IMM Network event

Serviceable:

No

CIM Information: Prefix:

IMM and

ID:

0001

SNMP Trap ID:

37

Automatically notify Support:

No

User response:

Information only; no action is

required.

40000002-00000000

Certificate Authority [arg1] has

detected a [arg2] Certificate Error.

Explanation:

This message is for the use case when

W.580A2 • 40000002-00000000

30

System x iDataPlex dx360 M4 Types 7912 and 7913: Problem Determination and Service Guide

«
...
46
47
48
49
50
...
»

Содержание System x iDataPlex dx360 M4 7912

















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для System x iDataPlex dx360 M4 7912

EMC PowerEdge MX7000

Бренд: Dell Страницы: 68

Бренд: Supermicro Страницы: 80

Бренд: Supermicro Страницы: 104

SnapServer EXP E2000 Expansion Array

Бренд: Overland Storage Страницы: 2

Бренд: THOMSON Страницы: 52

Бренд: NI Страницы: 22

Бренд: Moxa Technologies Страницы: 6

NMR AV4 BSMS System

Бренд: Bruker Страницы: 234

Бренд: ADC Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды