IBM System x iDataPlex dx360 M4 7912, Руководство по обслуживанию

Страница: 25 / 400

Features and specifications
The following information is a summary of the features and specifications of the
server. Depending on the server model, some features might not be available, or
some specifications might not apply.
Table 1. Features and specifications
Microprocessor:
v
Supports up to two Intel Xeon E5-2600
series multi-core microprocessors
v QuickPath Interconnect (QPI) links
speed up to 8.0 GT per second
Note:
v
Use the Setup utility program to
determine the type and speed of the
microprocessors.
v For a list of supported microprocessors,
see http://www.ibm.com/servers/eserver/
serverproven/compat/us/.
Hard disk drives: The system-board tray
and GPGPU enclosure support one
3.5-inch simple-swap SATA, two 2.5-inch
simple-swap SATA/SAS or solid-state
drives, or four 1.8-inch simple-swap
solid-state drives.
Expansion slots: Up to four PCI Express
slots per chassis. Support for the following
riser cards:
v
2U Compute server
– Four PCI Express x16 (x8
mechanically) slots (PCIe3.0,
full-height, half-length)
v 2U GPGPU server
– Two PCI Express x16 (x8
mechanically) slots (PCIe3.0,
full-height, half-length)
– Two PCI Express x16 (x16
mechanically) slots (PCIe3.0,
full-height, full-length)
Memory:
v Minimum: 2 GB
v Maximum: 512 GB
– 64 GB using Unbuffered DIMMs
(UDIMMs)
– 128 GB using Registered DIMMs
(RDIMMs)
– 512 GB using Load Reduction
DIMMs (LRDIMMs)
v Type: PC3-6400, PC3-8500,
PC3-10600, PC3-12800, or
PC3-14900 (single-rank, dual-rank, or
quad-rank), ECC registered or
unbuffered double-data-rate 3 (DDR3)
1066, 1333, 1600, and 1866 MHz
SDRAM DIMMs
v
Slots: 16 (eight per microprocessor)
v
Supports (depending on the model):
– 2 GB and 4 GB Unbuffered DIMMs
– 2 GB, 4 GB, 8 GB, and 16 GB
Registered DIMMs
– 32 GB Load Reduced DIMMs
Environment:
v
Air temperature:
– Server on: 5°C to 40°C (41°F to
104°F); altitude: 0 to 950 m (0 to
3116 ft). Derate maximum
temperature by 1°C for every 175
m (574 ft) increase in elevation to
a maximum of 3050 m (10004 ft) at
an ambient temperature of 5°C to
28°C (41°F to 82°F)
Notes:
1. microprocessor E5-2690:
temperature: 5°C to 35°C (41°F
to 95°F); altitude: 0 to 950 m (0
to 3116 ft)
2. GPGPU node: temperature:
5°C to 35°C (41°F to 95°F);
altitude: 0 to 950 m (0 to 3116
ft)
3. Intel Xeon Phi 7120P:
temperature: 5°C to 27°C (41°F
to 80.6°F); altitude: 0 to 304.8
m (0 to 1000 ft)
– Server off: 5°C to 45°C (41°F to
113°F); maximum altitude: 0 to
3050 m (10004 ft)
– Storage (non-operating): 1°C to
60°C (33.8°F to 140°F); altitude: 0
to 3050 m (0 to 10004 ft).
– Shipment (non-operating): -40°C to
60°C (-40°F to 140°F); altitude: 0
to 10700 m (0 to 35105 ft).
Environment (continued):
v
Humidity:
– Server on: non-condensing: -12°C
dew point (10.4°F), 8% to 85%;
maximum dew point: 24°C (75°F);
maximum rate of change: 5°C/hr
(41°F/hr) for tape drive and
microprocessor models from 115 W to
130 W and 135 W, 20°C/hr (68°F/hr)
for HDDs
– Server off: 8% to 85%; maximum dew
point: 27°C (80.6°F); maximum rate of
change: 5 °C/hr for microprocessor
models from 60 W to 95 W
– Storage (non-operating): 5% to 80%;
maximum dew point: 29°C (84.2°F)
– Shipment (non-operating): 5% to
100%; maximum dew point: 29°C
(84.2°F)
v
Particulate contamination:
Attention:
– Design to ASHRAE Class A3,
temperature: 36°C to 40°C (96.8°F to
104°F) with relaxed support:
- Support cloud such as workload
with no performance degradation
acceptable (turbo-off)
- Under no circumstance, can any
combination of worst case
workload and configuration result in
system shutdown or design
exposure at 40°C
- The worst case workload (such as
Linpack,Turbo-On) may have
performance degradation
– Airborne particulates and reactive
gases acting alone or in combination
with other environmental factors such
as humidity or temperature might
pose a risk to the server. For
information about the limits for
particulates and gases, see
“Particulate contamination” on page
369.
Chapter 2. Introduction
7