HP HPE Synergy 12000 Frame Скачать руководство пользователя страница 95

Страница: 95 / 183

Installing the

Installing the storage module

storage module

Prerequisites

CAUTION:

Installation of the storage module into the frame without drives requires one person. Installation of the storage module

into the frame with drives already installed requires two people.

Be sure that you have the required number of people to lift the storage module into the frame.

Procedure

1. Before installing the storage module, press down the storage module release latch to open the storage module handle.

NOTE:

NOTE: The storage module handle arrives packaged in the closed position and must be opened prior to installation.

2. Install the storage module. To fully seat the storage module, be sure to close the storage module handle. When the handle is

completely closed, the release latch clicks into place.

Installing the storage module

Содержание HPE Synergy 12000 Frame
























































































































































































Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды

HP HPE Synergy 12000 Frame, Руководство по установке и настройке

Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды