manualshive.com logo in svg

HP HPE Synergy 12000 Frame, Руководство по установке и настройке

Поделиться
Скачать
HP HPE Synergy 12000 Frame Скачать руководство пользователя страница 44

11

LINK port

SFP+ connector that provides the following functions:

IMPORTANT:

IMPORTANT:

Use supported SFP+ 10GbE DAC cables or transceivers for LINK port
connections. For more information, see the product QuickSpecs on the
Hewlett Packard Enterprise website

Hewlett Packard Enterprise website .

Provides high availability management network connectivity between:

LINK ports on two frame link modules in the same frame for a single frame
configuration

Frame link modules in different frames as part of a management network ring in
a multiframe configuration

Provides management ring (frame link topology) connectivity for automatic frame
discovery by HPE OneView.

12

MGMT port

SFP+ connector that provides the following functions:

IMPORTANT:

IMPORTANT:

Use supported SFP+ DAC cables or transceivers for MGMT port connections.
For more information, see the product QuickSpecs on the Hewlett Packard

Hewlett Packard

Enterprise website

Enterprise website.

IMPORTANT:

IMPORTANT:

The transceiver or cable used must match the port speed of the switch used
for management network connectivity.

Provides a management uplink to the management network.

10GbE or 1GbE based on the cable or transceiver used.

Item

Item

Description

Description

Function

Function

HPE Synergy 4-Port Frame Link Module components and LEDs

44

Содержание HPE Synergy 12000 Frame
























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды