HP HPE Synergy 12000 Frame Скачать руководство пользователя страница 70

Страница: 70 / 183

Installing the frame in a rack-free environment

WARNING:

WARNING: To reduce the risk of personal injury or damage to the equipment in a rack-free

environment:

Never stack the frame on top of another frame.
Never place equipment on top of the frame.
Never place the frame on a surface that cannot support up to 249.50 kg (550.00 lb).

Procedure

1. Select the location for the frame.

For more information, see Rack-free environment requirements.

2. Remove components from the frame.

3. Place the frame on a flat, sturdy surface to support the frame.

4. Complete the component installation for your configuration.

Installing the frame in a rack-free environment

Содержание HPE Synergy 12000 Frame
























































































































































































Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды

HP HPE Synergy 12000 Frame, Руководство по установке и настройке

Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды