HP HPE Synergy 12000 Frame Скачать руководство пользователя страница 154

Страница: 154 / 183

The

The HPE

HPE Synergy Console

Synergy Console cannot connect to HPE OneView

cannot connect to HPE OneView

If the HPE Synergy Console cannot connect to HPE OneView, the following Attention screen appears.

If you are unable to connect to HPE OneView, perform the following troubleshooting solutions.

Procedure

1. Connect to the HPE Synergy Console through a different frame.

2. Reconnect to HPE OneView.

3. Verify there are no more than three live HPE OneView sessions within the management network. Any initiated sessions after three

will not be able to connect to HPE OneView.

HPE Synergy Console also has icons available for further navigation. For more information, see HPE Synergy Console icons.

The HPE Synergy Console cannot connect to HPE OneView

154

Содержание HPE Synergy 12000 Frame
























































































































































































Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды

HP HPE Synergy 12000 Frame, Руководство по установке и настройке

Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды