HP HPE Synergy 12000 Frame Скачать руководство пользователя страница 76

Страница: 76 / 183

Installing the

Installing the frame

frame into the rack

into the rack

WARNING:

WARNING: When lifting the frame with the optional removable handles, always use at least four

people to lift the frame into the rack. If the frame is being loaded into the rack above chest level,

a fifth person must assist with aligning the frame with the rails while the other four people

support the weight of the frame.

NOTE:

NOTE: You can install the frame into the rack using a mechanical lift. When using a mechanical lift, two people are

required for the frame installation. If you choose the mechanical lift installation, resume the frame installation at step 5.

Procedure

1. Attach the lift handles to the frame.

a. Align each lift handle to the frame spools.

b. Press the release button, and then pull the lift handle up until it locks in place.

2. Line up the frame with the rack, set the back end of the frame on the rack rails and slide it in.

Installing the frame into the rack

Содержание HPE Synergy 12000 Frame
























































































































































































Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды

HP HPE Synergy 12000 Frame, Руководство по установке и настройке

Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды