HP HPE Synergy 12000 Frame Скачать руководство пользователя страница 73

Страница: 73 / 183

Installing the rack rails for a square-hole rack

Rack rails are marked "LEFT" and "RIGHT" for identification. The rail release levers are used only when removing the rail from the rack.

Procedure

1. Begin with the left rack rail. Shorten the rail.

2. Align the rear end of the rail with the rack rear column.

3. Position the rail tabs next to the square openings in the rack rear column.

4. Keeping the rail level, insert the rear rail tabs into the rack rear column, and push the tabs down into place.

5. Extend the front of the rack rail to the rack front column.

6. Position the rail tabs next to the square openings in the rack front column.

7. Insert the front rail tabs into the rack front column and push the tabs down into place.

Installing the rack rails for a square-hole rack

Содержание HPE Synergy 12000 Frame
























































































































































































Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды

HP HPE Synergy 12000 Frame, Руководство по установке и настройке

Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды