manualshive.com logo in svg

HP HPE Synergy 12000 Frame, Руководство по установке и настройке

Поделиться
Скачать
HP HPE Synergy 12000 Frame Скачать руководство пользователя страница 146

Configuring 

Configuring HPE

HPE Synergy Image Streamer

 Synergy Image Streamer

HPE Synergy Image Streamer can be used to deploy OS build artifacts to the  HPE Synergy compute modules. However, it must be

installed and configured within HPE OneView.

Procedure

Procedure

1.  Create a management network that is consistent with the  HPE OneView management network.

2.  Add an IPv4 subnet and address range.

Define the range of IPv4 addresses and subnets to set aside for each  Image Streamer in the frame link topology, plus the number of
operating system servers expected to be deployed.

3.  Add an OS deployment server for use in  HPE OneView to deploy operating systems to managed servers.

4.  Create a deployment network to enable operating system deployment to compute modules using  Image Streamer.

5.  Create one or more logical interconnect groups to define the connections between Image Streamers and the compute modules they

support.

6.  Create an enclosure group that includes the  Image Streamer configuration.

7.  Create a logical enclosure to define the set of frames to which to apply the  Image Streamer enclosure group.

For more information about configuring  HPE Synergy Image Streamer, see the HPE OneView Help for HPE Synergy or the HPE OneView
User Guide for HPE Synergy on the  Hewlett Packard Enterprise website (http://www.hpe.com/info/synergy-docs

http://www.hpe.com/info/synergy-docs).

Configuring HPE Synergy Image Streamer

146

Содержание HPE Synergy 12000 Frame
























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды