HP HPE Synergy 12000 Frame Скачать руководство пользователя страница 166

Страница: 166 / 183

Frame link module factory reset

IMPORTANT:

When a frame is configured and is actively managed by HPE OneView, a factory reset should be performed only when

required by a recommended HPE OneView management or service process.

The Factory Reset action resets all frame link modules in a frame to factory default settings. Resetting a frame link module to factory

default settings will take the frame link module offline for up to 10 minutes. If the frame link module is installed in a frame managed by

HPE OneView, the frame link module will be reclaimed by HPE OneView after the factory reset is complete.

Some instances in which a factory reset might be necessary include:

Prior to moving a frame to a new HPE OneView environment.

After performing a factory reset of the HPE Synergy Composer that manages the frame.

For more information, see the HPE OneView for HPE Synergy documentation (https://www.hpe.com/info/synergy-docs

https://www.hpe.com/info/synergy-docs).

Frame link module factory reset

166

Содержание HPE Synergy 12000 Frame
























































































































































































Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды

HP HPE Synergy 12000 Frame, Руководство по установке и настройке

Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды