HP HPE Synergy 12000 Frame Скачать руководство пользователя страница 167

Страница: 167 / 183

Performing a frame link module factory reset

NOTE:

This procedure only factory resets the frame link modules installed in the frame. It does not factory reset any other

components installed in the frame.

NOTE:

The frame link module can be factory reset by pressing the front panel reset button until the front panel UID flashes or

by using the HPE Synergy Console Actions menu. Hewlett Packard Enterprise recommends using the HPE Synergy

Console to perform a factory reset.

Procedure

1. Connect to the HPE Synergy Console.

2. Select Actions > FLM Diagnostics > Factory Reset.

3. Click Yes, reset.

Performing a frame link module factory reset

167

Содержание HPE Synergy 12000 Frame
























































































































































































Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды

HP HPE Synergy 12000 Frame, Руководство по установке и настройке

Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды