HP HPE Synergy 12000 Frame Скачать руководство пользователя страница 126

Страница: 126 / 183

Connecting to the HPE Synergy Console using a keyboard, video monitor, and mouse

NOTE:

This procedure describes connecting a keyboard and mouse to a monitor with an integrated USB hub. Alternatively, you

can use a standalone USB hub to connect a keyboard and mouse.

NOTE:

Cabling to an HPE Synergy 4-Port Frame Link Modules requires an HPE Synergy 4-Port Frame Link Module USB Adapter

Prerequisites

A frame link module is installed in a frame link module bay.

Procedure

1. Connect a monitor cable to the monitor port and connect a USB cable to the USB port on either:

The front panel module on the front of the frame.

Either frame link module on the rear of the frame.

Connecting to the HPE Synergy Console using a keyboard, video monitor, and mouse

126

Содержание HPE Synergy 12000 Frame
























































































































































































Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды

HP HPE Synergy 12000 Frame, Руководство по установке и настройке

Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды