HP HPE Synergy 12000 Frame Скачать руководство пользователя страница 79

Страница: 79 / 183

Component installation

The following sections contain installation instructions for the individual frame components. The images included in these instructions

are intended to illustrate how the components are installed. These images are not intended to indicate the location for installation. Install

the component in the bay from which it was removed earlier in this document.

There is no specific installation order requirement for the frame components, however Hewlett Packard Enterprise recommends

installing all front components first, followed by all rear components.

All components must be installed and cabled before you power up the frame.

The frame and components automatically power on when power is connected.

Component installation

Содержание HPE Synergy 12000 Frame
























































































































































































Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды

HP HPE Synergy 12000 Frame, Руководство по установке и настройке

Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды