HP HPE Synergy 12000 Frame Скачать руководство пользователя страница 80

Страница: 80 / 183

Installing an

Installing an appliance module

appliance module

The appliance modules have specific population guidelines based on the appliance module and the system configuration. As a best

practice, if two appliance modules of the same type exist in any group of linked frames, install the appliance modules in separate frames.

After all components are installed and cabled, be sure to reimage the appliance module before bringing the appliance module into your

HPE Synergy configuration. Updating the firmware, ensures that the appliance module is compatible with the HPE Synergy Software

Release installed on HPE Synergy. For more information, see Update the firmware.

Procedure

1. If installed, remove the appliance module blank from the appliance bay.

2. Install the first appliance module into appliance bay 1.

When the appliance module is fully seated, it locks into place.

Installing an appliance module

Содержание HPE Synergy 12000 Frame
























































































































































































Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды

HP HPE Synergy 12000 Frame, Руководство по установке и настройке

Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды