manualshive.com logo in svg

HP HPE Synergy 12000 Frame, Руководство по установке и настройке

Поделиться
Скачать
HP HPE Synergy 12000 Frame Скачать руководство пользователя страница 112

Power supply configurations

Power supply configurations

Sufficient power supplies must be installed to support the installed devices and interconnect modules. Power estimates for HPE Synergy

can be provided using either the HPE Synergy Planning Tool or the HPE Power Advisor. For more information about the HPE Power
Advisor or the HPE Synergy Planning Tool, see the Data Center Infrastructure Advisor page (https://dcia.itcs.hpe.com/

https://dcia.itcs.hpe.com/).

The number of supported power supplies in the  frame range from a minimum of two to a maximum of six power supplies. There are no

power supply bay placement restrictions of power supplies in the frame. However, for best cooling and power distribution,  Hewlett

Packard Enterprise recommends the following best practice for power supply usage.

NOTE: 

NOTE: The default power mode is Redundant power feed mode.

Number of power

Number of power

supplies

supplies

Power modes

Power modes

Power supply bay (power feed)

Power supply bay (power feed)

1

Not supported

—

2

Redundant power supply mode

Redundant power feed mode

1(A) and 3(A)

1(A) and 3(B)

3

Redundant power supply mode

1(A), 3(A), and 5(A)

4

Redundant power supply mode

Redundant power feed mode

1(A), 3(A), 4(A), and 6(A)

1(A), 3(B), 4(A), and 6(B)

5 

Redundant power supply mode

1(A), 2(A), 3(A), 4(A), and 6(A)

6

Redundant power supply mode

Redundant power feed mode

1(A), 2(A), 3(A), 4(A), 5(A), and 6(A)

1(A), 2(A), 3(B), 4(A), 5(B), and 6(B)

If an odd number of power supplies are installed in a  frame that is configured for redundant power feed mode, all power supplies are

providing power to the frame, but the capacity of the odd power supply is not used to determine the overall power capacity of the

frame.

To enhance cooling, populate all power supply bays with either a power supply blank or a power supply.

Power supply configuration recommendations for the  frame do not depend on the type of power supply being used. However, all power

supplies must be of the same type. Mixed-type power supply configurations are not supported.

1

1

1

Power supply configurations

112

Содержание HPE Synergy 12000 Frame
























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды