HP HPE Synergy 12000 Frame Скачать руководство пользователя страница 39

Страница: 39 / 183

Storage module LEDs

The front panel and LED layout shown in the following illustration is an example. Depending on your specific model, the LEDs might be

different.

Item

Item LED

LED

Status

Definition

Drawer status

Solid green

Drive drawer is closed

Flashing green Drive drawer is open

Flashing amber Thermal warning, close the drive drawer

UID

Solid blue

One or more drives are being located

Flashing blue

Firmware flash in progress

Off

No drives are being located

Health status

Green

Normal operation

Flashing amber Degraded condition

Flashing red

Critical condition

Drive status (in priority order) Solid amber

One or more drives failed

Flashing amber One or more drives are predicted to fail

Flashing green One or more drives are rebuilding or transforming

Solid green

One or more drives are members of a logical drive

Off

No drives are configured by a RAID controller

Drawer power

Green

Storage module is in use, do not remove

Off

Storage module is not in use, safe to remove

The drive drawer must be closed within five minutes after it is opened.

Storage module LEDs

Содержание HPE Synergy 12000 Frame
























































































































































































Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды

HP HPE Synergy 12000 Frame, Руководство по установке и настройке

Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды