HP HPE Synergy 12000 Frame Скачать руководство пользователя страница 142

Страница: 142 / 183

Update the HPE Synergy appliance firmware

IMPORTANT:

To ensure compatibility, each HPE Synergy Composer installed into an HPE Synergy solution must be on the same

firmware level. Similarly, each HPE Synergy Image Streamer must be on the same firmware level. If the appliance pair is

not on the same firmware level, a reimage of the appliance module with the older firmware level is required.

If both appliance modules in a redundant pair are on the same firmware version, use HPE OneView to update to the latest firmware

version.

For more information about reimaging the appliance firmware, see Validating HPE Synergy appliance firmware: Preparing an HPE
Synergy appliance for first-time setup on the Hewlett Packard Enterprise website (http://www.hpe.com/info/synergy-docs

http://www.hpe.com/info/synergy-docs).

Update the HPE Synergy appliance firmware

142

Содержание HPE Synergy 12000 Frame
























































































































































































Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды

HP HPE Synergy 12000 Frame, Руководство по установке и настройке

Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды