manualshive.com logo in svg

HP HPE Synergy 12000 Frame, Руководство по установке и настройке

Поделиться
Скачать
HP HPE Synergy 12000 Frame Скачать руководство пользователя страница 63

HPE Synergy 40Gb F8 Switch Module LEDs and buttons

HPE Synergy 40Gb F8 Switch Module LEDs and buttons

Item

Item

Description

Description

Status

Status

1

Interconnect link port LEDs

Solid green = Linked
Solid red = Error detected .

Off = No link

2

QSFP+ port LEDs

The four LEDs above each port correspond to the 10GbE or 8Gb FC
channels of the port. The LEDs display one of four modes:
Ethernet mode:

Solid green = The port is configured as an Ethernet port.

Off = The port is not configured as an Ethernet port.

PID mode:

Solid green = The port is configured as an uplink port.

Solid amber = The port is configured as a stacking port.

Solid purple = The port is configured as a mirrored port.

Solid red = Error.

Solid blue = Activated by OneView for port identification.

Off = The port is not configured.

Link/Activity mode:

Solid green = 10Gb Ethernet link

Flashing green = 10Gb Ethernet activity

Solid amber = 8Gb FC link

Flashing amber = 8Gb FC activity

Solid purple = 40Gb Ethernet link

Flashing purple = 40Gb Ethernet activity

Solid Red = Error

Off = No link

Fibre Channel (FC) mode:

Solid green = The port is configured as an FC port.

Off = The port is not configured as an FC port.

To switch between the LED modes, press the NEXT button.

3

NEXT button

Selects the QSFP+ port LED mode.

4

Reset pin-hole

Resets the module

1

HPE Synergy 40Gb F8 Switch Module LEDs and buttons

63

Содержание HPE Synergy 12000 Frame
























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды