HP HPE Synergy 12000 Frame Скачать руководство пользователя страница 69

Страница: 69 / 183

Removing components from the

Removing components from the frame

frame

Before installing the frame into the rack, you must remove all of the pre-installed components from the front and rear of the frame.

Because a fully-populated frame can weigh up to 249.50 kg (550.00 lb), removing the components from the frame makes moving and

installing the frame easier.

With the frame still on the pallet, remove all components from the front and rear of the frame.

IMPORTANT:

IMPORTANT: To ensure the correct configuration when installing components, be sure to note the location of each

component before removing it from the frame.

For specific instructions concerning removing the components, see the HPE Synergy 12000 Frame Maintenance and Service Guide.

Removing components from the frame

Содержание HPE Synergy 12000 Frame
























































































































































































Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды

HP HPE Synergy 12000 Frame, Руководство по установке и настройке

Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды