HP HPE Synergy 12000 Frame Скачать руководство пользователя страница 11

Страница: 11 / 183

WARNING:

To reduce the risk of electric shock or damage to the equipment, enter a frame or perform

service on system components only as instructed in the user documentation.

WARNING:

A risk of electric shock from high leakage current exists. Before connecting the AC supply to the

power enclosure, be sure that the electrical outlets are properly grounded (earthed).

CAUTION:

Always be sure that equipment is properly grounded and that you follow proper grounding procedures before beginning

any installation procedure. Improper grounding can result in ESD damage to electronic components. For more

information, see Electrostatic discharge.

CAUTION:

CAUTION: Protect the storage module from power fluctuations and temporary interruptions with a regulating UPS. This

device protects the hardware from damage caused by power surges and voltage spikes and keeps the storage module in

operation during a power failure.

Warning, caution, and important messages

Содержание HPE Synergy 12000 Frame
























































































































































































Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды

HP HPE Synergy 12000 Frame, Руководство по установке и настройке

Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды