HP HPE Synergy 12000 Frame Скачать руководство пользователя страница 19

Страница: 19 / 183

Rack-free environment requirements

The HPE Synergy 12000 Frame (referred to as the frame) can be used in a rack-free environment. The following conditions must be met

when performing a rack-free installation:

A fully-populated frame can weigh up to 249.50 kg (550.00 lb). The object supporting the frame must be able to withstand this
weight.

Always place the frame on a sturdy, flat surface.

WARNING:

WARNING: To reduce the risk of personal injury or damage to the equipment in a rack-free

environment:

Never stack the frame on top of another frame.
Never place equipment on top of the frame.
Never place the frame on a surface that cannot support up to 249.50 kg (550.00 lb).

Rack-free environment requirements

Содержание HPE Synergy 12000 Frame
























































































































































































Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды

HP HPE Synergy 12000 Frame, Руководство по установке и настройке

Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды