HP HPE Synergy 12000 Frame Скачать руководство пользователя страница 34

Страница: 34 / 183

Compute module LEDs and buttons

Item

Item Description

Description

Status

UID LED

Solid blue = Activated

Flashing blue (1 Hz/cycle per sec) = Remote management or firmware upgrade in
progress

Off = Deactivated

Health status LED

Solid green = Normal

Flashing green (1 Hz/cycle per sec) = HPE iLO is rebooting

Flashing amber = System degraded

Flashing red (1 Hz/cycle per sec) = System critical

Mezzanine NIC status LED

Solid green= Link on any Mezzanine NIC

Flashing green= Activity on any Mezzanine NIC

Off = No link or activity on any Mezzanine NIC

Power On/Standby button and system power
LED

Solid green = System on

Flashing green (1 Hz/cycle per sec) = Performing power on sequence

Solid amber = System in standby

Off = No power present

If all other LEDs are off, then no power is present to the compute module. If the health LED is flashing green while the system power

LED is off indicates that the Power On/Standby button service is initializing or that an iLO reboot is in progress. Facility power is not

present, power cord is not attached, no power supplies are installed, power supply failure has occurred, or the power button cable is

disconnected.

Compute module LEDs and buttons

Содержание HPE Synergy 12000 Frame
























































































































































































Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды

HP HPE Synergy 12000 Frame, Руководство по установке и настройке

Результаты поиска

Содержание HPE Synergy 12000 Frame

Отзывы:

Бренды по названию

Популярные бренды