manualshive.com logo in svg

HP HPE Synergy 12000 Frame, Руководство по установке и настройке

Поделиться
Скачать
HP HPE Synergy 12000 Frame Скачать руководство пользователя страница 27

Device bay numbering

Device bay numbering

All device bays in the  frame are numbered in consecutive order from lowest to highest, from left to right from top to bottom, as observed

by a user looking directly at the frame.

Devices larger than half-height (multi-bay devices) are numbered according to the lowest device bay number that the multi-bay device

occupies.

For an even number of device modules, they must be installed next to each other between sets of vertical partitions if all device bays in

the frame are to be used.

For an odd number of single-wide full-height device modules, an even number must be installed next to each other between each vertical

partition, and the odd module must be installed in device bay 2 if all device bays in the frame are to be used.

The device bay numbering is available on the  Information pull tabs.

Device bay type

Device bay type

Device bay numbering

Device bay numbering

Single-wide, full-height

Single-wide, half-height

Single-wide, mixed-height

Double-wide, full-height

Double-wide, half-height

Double-wide, mixed-height

Device bay numbering

27

Содержание HPE Synergy 12000 Frame
























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды