manualshive.com logo in svg

HP HPE Synergy 12000 Frame, Руководство по установке и настройке

Поделиться
Скачать
HP HPE Synergy 12000 Frame Скачать руководство пользователя страница 46

6

USB port

Allows connection to the frame using a supported USB device. Devices include a
keyboard or mouse for connecting to the HPE Synergy Console. To connect multiple
devices, a USB hub (not included) is required.

Used for performing a USB recovery frame link module firmware update.

7

LINK port activity
LED

Reports LINK port activity:

Flashing green = Activity on the LINK port

Off = No activity on the LINK port

8

LINK port

A 10GBASE-T RJ45 connector that provides two functions:

Provides high-availability management network connectivity between:

LINK ports on two frame link modules in the same frame for a single frame
configuration.

Frame link modules in different frames as part of a management network ring in
a multiframe configuration.

Provides management ring (frame link topology) connectivity for automatic frame
discovery by HPE OneView.

9

LINK port
connectivity LED

Reports LINK port connectivity:

Solid green = LINK port is connected.

Off = LINK port is not connected.

10

Monitor port

Allows connection to the frame using a monitor device or an active monitor port
adapter.

Item

Item

Description

Description

Function

Function

HPE Synergy Frame Link Module components and LEDs

46

Содержание HPE Synergy 12000 Frame
























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды