manualshive.com logo in svg

HP HPE Synergy 12000 Frame, Руководство по установке и настройке

Поделиться
Скачать
HP HPE Synergy 12000 Frame Скачать руководство пользователя страница 72

Measuring with the rack template

Measuring with the rack template

The HPE Synergy 12000 Frame Rack Template  ships with the  frame. The rack template provides detailed instructions on where to

position the frame and rack rails, and where to install the cage or clip nuts. Each  frame kit includes the rack rails recommended for that

frame.

NOTE: 

NOTE: Four cage nuts and four clip nuts are included with the frame. Always use cage nuts in racks with square holes.

Always use clip nuts in racks with round holes.

When installing multiple frames, install the rack rails and cage nuts for one  frame, and then install the  frame. Repeat for each additional

frame.

Procedure

Procedure

1.  Install lower cage nuts (left and right) in the front of the rack at the bottom of the fourth U (10 holes up on the template).

2.  Install the upper cage nuts (left and right) in the front of the rack at the bottom of the tenth U (28 holes up on the template).

3.  Install the rack rails.

Measuring with the rack template

72

Содержание HPE Synergy 12000 Frame
























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды