Hioki 3155-01 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 366

Hioki 3155-01 Скачать руководство пользователя страница 16

iv

────────────────────────────────────────────────────

Notes on Use

────────────────────────────────────────────────────

CAUTION

・

In order to avoid electric shock, turn off the power to all devices before
plugging in or unplugging the measurement network or RS-232C connector.

・

When unplugging the power cord from the power receptacle or from the unit,
grasp the plug, not the cord, in order to avoid damaging the cable.

・

To avoid damaging the leads or probes, do not bend or pull the leads or
probes.

・

Use caution when taking measurements in circuits where the power line are
hot.

・

For safety reasons, only use the 9195 or 9170 probe / test lead provided with
the unit, or the optional 9461 or 9287 for measurement.

・

The changing of the function when replacing the test terminals requires
disconnection of the test leads from the equipment being measured and then
the disconnection of the test leads from the terminals.

・

To avoid damage to the unit, do not short the output terminal and do not
input voltage to the output terminal.

・

Use the unit near the power receptacle.

WARNING

The 9196 APPLY UNIT used in the measurement of enclosure leakage
current, patient leakage current

and patient leakage current

continuously outputs voltage while the voltage application button is
being pressed. Care is required to avoid accidents caused by electrical
shock.

The leakage current measurement terminals, the resistance
measurement terminals and the RS-232C connector are not insulated.
Handle these items carefully in order to avoid electric shock or a short
circuit accident.

If the end of a lead or a probe short-circuits lines with a voltage between
them, this is very dangerous and can lead to a serious accident.
Exercise great care when measuring voltages.

In the event that the equipment malfunctions in any manner during use,
turn off the power immediately, and contact your dealer or HIOKI
representative.

Connection

During measurement

«
...
14
15
16
17
18
...
»

Содержание 3155-01















































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды