32
2.3.6.4. Program Siren
<
<
I
I
M
M
P
P
O
O
R
R
T
T
A
A
N
N
T
T
N
N
O
O
T
T
E
E
>
>
)
Program Siren
option will be
available in
/-
menu only
when any detector or Remote
Controller has been added already.
)
This feature is available for
868 AM &
FM
only.
If an outdoor Bell Box (BX-8/BXA-8) or Indoor
Siren (SR-8/SRA-8), is to be included in the
system, it should be programmed first by the
Control Panel, so that the Control Panel can
communicate with these auxiliary devices.
To program these auxiliary devices, select
Program Siren
in the
/-
menu.
L e a r n S i r e n
S i r e n T a m p O f f
S i r e n T a m p O n
C
o
n
f i r m O
n
C o n f i r m O f f
E n t r y S n d O n
E n t r y S n d O f f
z
Learn Siren
If any detector or Remote Controller has
been added already:
Step 1
. Put the desired Auxiliary sirens into
learn mode (Please refer to their
individual Operation Manual).
Step 2
.
Move the cursor to the position
Learn
Siren
and press
OK
key. The screen
displays:
o S i n g l e a r e a
Wh o l e s y s t e m
Single area
means that BX/SR raises
an alarm only when the sensor, which is
learnt in this area, is triggered.
Whole system
means that BX/SR
raises an alarm when any sensor,
which is learnt in either Area 1 or Area 2,
is triggered.
Step 3
. Select either
Single area
or
Whole
System
and press
OK
key; the
screen displays “
Pls wait RF
transmitting
” and a learning code is
transmitted to BX/SR (please refer to
the operation manual of the devices
to finish the further process).
Step 4
. After exiting the auxiliary devices out
of Learn mode, the learning process is
then complete.
<
<
N
N
O
O
T
T
E
E
>
>
)
If any of these devices does not
respond, make sure that the device is
in learn mode and repeat all steps.
)
Once they are learnt-in, a PIN code
plus
OK
key will make the Control
Panel to transmit a signal to all of
them.
<
<
I
I
M
M
P
P
O
O
R
R
T
T
A
A
N
N
T
T
N
N
O
O
T
T
E
E
>
>
)
The following option is only available
for setting the already learnt-in sirens.
Any setting changes apply to all sirens.
z
Siren Tamp. On, Siren Tamp. Off
This is to enable or disable all siren tamper
remotely. It is specially designed for
replacing battery.
z
Disable the Siren tamper switch by
selecting
Siren Tamp. Off
. All added
sirens will temporarily lose their
Tamper Protection for an hour.
z
Enable the Siren tamper switch by
selecting
Siren Tamp. On
again. All
added sirens will be enabled with
Tamper protection simultanously.
<
<
N
N
O
O
T
T
E
E
>
>
)
Siren tamper disable will automatically
revert to
On
after an hour if it is not
switchd back remotely.
z
Confirm On, Confirm Off
This is to enable or disable all sirens to
play system arming or disarming
confirmation beeps.
z
Disable the Siren Confirmation by
selecting
Confirmation Off
.
z
Enable the Siren Confirmation by
selecting
Confirmation On
.
Содержание CTC-1241GT
Страница 1: ...f 25 MAR 2010 For THIRKILD DENMARK...
