Gardsman CTC-1241GT, Руководство по установке

Страница: 18 / 73

14
<
<
N
N
O
O
T
T
E
E
>
>
)
The Latch rpt On/Off section display
for your programming only when the
Latch selection function is enabled
(See section 2.5.4 under Configuring
your system)
)
The latch reporting function can be set
respectively for each PIN code.
)
Latch Report ON = Whenever the
system is armed, home/ day home/
night home armed or disarmed, the
Panel will transmitt Contact ID code /
SMS message / GPRS reporting
(according to pre-setting) to notify the
Central Monitoring Station.
)
Latch Reprot OFF = Whenever the
system is armed, home/ day home/
night home armed or disarmed, the
Panel will NOT transmitt reporting(s)
to notify the Central Monitoring Station.
Step 6. Choose whether you wish to enable or
disable the latch report option and
press
OK .
Step 7 . You are then requested to give a name
for this new PIN code.
U s e r N a m e
_
<
<
N
N
O
O
T
T
E
E
>
>
)
A max of 10 characters is allowed for
user name.
Step 8. Press OK to confirm the new name. If
no name is wished, press OK directly.
* 1 ) M R . S M I T H
2 ) M R S . S M I T H
3 )
¿ ¿ ¿ ¿
4 ) . . . .
<
<
N
N
O
O
T
T
E
E
>
>
)
2) MRS. SMITH represents User # 2
PIN code is set up, and a user name
is specified.
)
3)
¿¿¿¿
represents User # 3 PIN
code is setup, but without a user
name specified.
)
4) ●●●● represents User # 4 PIN code
is not yet set up for activation.
Step 9. Proceed to set additional User PIN
Codes as instructed from Steps 1-8.
< < I I M M P P O O R R T T A A N N T T N N O O T T E E > >
)
To name the User Names, please
refer to section 5. Appendix, Naming
section for more information.
)
If the code is not correct, a Code is
not ncorrect prompt message will be
displayed 2 sec., and you are
requested to repeat Step 2 to enter
again.
)
The code cannot be duplicated with
any other codes. If the code has been
used, the screen will display
code in
use, select another and require you
re-enter a new code.
z
To Edit PIN Code
After the PIN Code is programmed, it can be
edited by following the steps below:
Step 1 . Move the cursor to the Pin Code
selection then press OK .
D e l e t e p i n - c o d e
( O K ? )
Step 2 . Press key, the next screen will ask
you to enter your new PIN code and
repeat it to confirm.
Step 3 . Make your selection whether to have
the Latch Key Reporting ON or OFF,
and then press
OK . The screen
returns to Code Setting menu, editing
the user PIN code is now completed.
z
To Delete User PIN code
Except User #1 which is activated by factory
default and can’t be deleted in any way, Users
(#2-6) PIN code can be deleted by following
the steps below:
Step 1 . Move the cursor to the PIN Code
selection then press OK . The
following screen will show the status
of each User PIN code:
* 1 ) M R . S M I T H
2 ) M R S . S M I T H
3 )
¿ ¿ ¿ ¿ ¿ ¿
4 ) . . . . . .