Freescale Semiconductor e200z3 Скачать руководство пользователя страница 294 | Manualshive

Страница: 294 / 442

background image

External Core Complex Interfaces

e200z3 Power Architecture Core Reference Manual, Rev. 2

7-26

Freescale Semiconductor

j_tdo

O

JTAG/OnCE serial output. Serial data is read from the OnCE block through

j_tdo.

State

Meaning

Data is shifted out the OnCE serial port lsb first.

Timing

When data is clocked out of the OnCE serial port,

j_tdo changes on the rising edge of

j_tclk. The j_tdo output is always driven. An external system-level TDO pin may be
three-statable and should be actively driven in the shift-IR and shift-DR controller states.
j_tdo_en indicates when an external TDO pin should be enabled, and is asserted during
the shift-IR and shift-DR controller states. In addition, for IEEE1149 compliance, the
system-level pin should change state on the falling edge of TCLK.

j_tms

I

JTAG/OnCE test mode select. Used to cycle through states in the OnCE debug controller. Toggling
j_tms while clocking with j_tclk controls transitions through the TAP state controller.

j_trst_b

I

JTAG/OnCE test reset. Resets the OnCE controller externally by placing it in the test-logic-reset state.
The following information details additional signals that can support external JTAG data registers using
the core TAP controller.
Signal Name

Type

Description

j_tst_log_rst

O

Indicates the TAP controller is in the test-logic-reset state

j_rti

O

JTAG controller run-test/idle state

j_capture_ir

O

Indicates the TAP controller is in the capture IR state

j_shift_ir

O

Indicates the TAP controller is in shift IR state

j_update_ir

O

Indicates the TAP controller is in update IR state

j_capture_dr

O

Indicates the TAP controller is in the capture DR state

j_shift_dr

O

Indicates the TAP controller is in shift DR state

j_update_gp_reg

O

Updates JTAG controller general-purpose data register

j_gp_regsel[0:11]

O

General-purpose external JTAG register select

j_en_once_regsel

O

External enable OnCE register select

j_key_in

I

Serial data from external key logic

j_nexus_regsel

O

External Nexus register select

j_lsrl_regsel

O

External LSRL register select

j_serial_data

I

Serial data from external JTAG register(s)

j_tst_log_rst

O

Test-logic-reset. Indicates whether the TAP controller is in test-logic-reset state.

State

Meaning

Asserted—The TAP controller is in test-logic-reset state.
Negated—The TAP controller is not in test-logic-reset state.

j_rti

O

Run-test/idle. Indicates whether the TAP controller is in the run-test/idle state.

State

Meaning

Asserted—The TAP controller is in run-test/idle state.
Negated—The TAP controller is not in run-test/idle state.

j_capture_ir

O

Capture IR. Indicates whether the TAP controller is in the Capture_IR state.

State

Meaning

Asserted—The TAP controller is in Capture_IR state.
Negated—The TAP controller is not in Capture_IR state.

j_shift_ir

O

Shift IR. Indicates whether the TAP controller is in the Shift_IR state.

State

Meaning

Asserted—The TAP controller is in Shift_IR state.
Negated—The TAP controller is not in Shift_IR state.

j_update_ir

O

Update IR. Indicates the TAP controller is in the Update_IR state.

State

Meaning

Asserted—The TAP controller is in Update_IR state.
Negated—The TAP controller is not in Update_IR state.

Table 7-22. Descriptions of JTAG Interface Signals (continued)

Signal

I/O

Signal Description

«
...
292
293
294
295
296
...
»

Содержание e200z3



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для e200z3

Netlink FRX8000

Бренд: Cabletron Systems Страницы: 94

MMAC-Plus 9E423-24

Бренд: Cabletron Systems Страницы: 10

MMAC-Plus 9A128-01

Бренд: Cabletron Systems Страницы: 22

Spectrum EMM-E6

Бренд: Cabletron Systems Страницы: 2

Бренд: Cabletron Systems Страницы: 54

Cabletron BRIM-F6

Бренд: Cabletron Systems Страницы: 43

Netlink FRX4000

Бренд: Cabletron Systems Страницы: 60

Бренд: Cabletron Systems Страницы: 8

Бренд: Cabletron Systems Страницы: 4

Бренд: Octavo Страницы: 28

Бренд: Obihai Страницы: 2

TWR-SB0410-36EVB

Бренд: NXP Semiconductors Страницы: 26

ThunderLAN TNETE100A

Бренд: Texas Instruments Страницы: 179

Бренд: ADS Technologies Страницы: 1

Бренд: Comelit Страницы: 19

Compact NVR-AS 4000

Бренд: IndigoVision Страницы: 38

Бренд: Freescale Semiconductor Страницы: 8

NVRx-7300 series

Бренд: Swann Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды