Fimer PVS-50-TL Скачать руководство пользователя страница 155

Страница: 155 / 171

155

000761AG-F

8 - Maintenance

- Error code

- Error message

- Warning

Name of Alarm and Cause

Solution

E079

- Wrong Sequence

Yellow LED

Incorrect Phases connection

(Only triphase models) The phases have not been

connected correctly to the AC output

• Invert two of the phases of the network wiring to the AC

terminal block of the inverter.

E081

- Internal Error

Red LED

Inverter fault / Incomplete inverter closing:

Fault inside the inverter or incomplete inverter closing

(front cover missing or not tightened, cable glands

missing or incorrectly tightened, environmental protec-

tion IP65 not guaranteed)

• If the problem has occurred during the installation phase or

during the inverter maintenance phase (therefore the cover

has been removed or the cable glands have been acted

upon), carry out the following operations:

- Disconnect the AC grid and DC input from the inverter

and check for the front cover and all the cable glands, also

checking their correct tightening to ensure environmental

protection IP65; reconnect the AC grid and the DC input and

attempt to switch the inverter on; if the problem persists, con-

tact customer assistance :

- If the front cover and all cable glands are present, discon-

nect the AC grid and DC input from the inverter and wait 15

minutes at a safe distance, then open the inverter cover and if

no smoke/smell of burning is present, check the integrity of the

components or the presence of moisture or other abnormal

conditions; reconnect the AC grid and DC input and attempt to

switch on the inverter; if the problem persists contact customer

assistance.

• If the problem has occurred after installation or after an in-

verter maintenance phase (therefore the cover has NOT been

removed or the cable glands have NOT been acted upon),

disconnect the AC grid and the DC input from the inverter and

contact customer assistance.

E084

- BackFeed OC

Yellow LED

Return current to photovoltaic field:

The error occurs if the input voltage is particularly low

(typically in the evening in conditions of low irradiation)

and indicates a return current from the inverter to the

photovoltaic panels).

If the error occurs in the evening or in conditions of low irra-

diation, it must not be considered a problem but a protection

intervention for the photovoltaic field.

- If the error occurs with good irradiation conditions, switch

the inverter off and back on again; if the error persists, contact

customer assistance.

E086

- Batt. 1 - F2

No LED

Error battery pack 1 unusable:

Indicates that the battery pack is unusable and must

be replaced.

• Error inside battery pack 1 and cannot be checked externally.

- If the problem (once the system has been switched off and

back on) persists, contact customer assistance.

E087

- Batt. 2 - F2

No LED

Error battery pack 2 unusable:

Indicates that the battery pack is unusable and must

be replaced.

• Error inside battery pack 2 and cannot be checked externally.

- If the problem (once the system has been switched off and

back on) persists, contact customer assistance.

E088

- Batt. 3 - F2

No LED

Error battery pack 3 unusable:

Indicates that the battery pack is unusable and must

be replaced.

• Error inside battery pack 3 and cannot be checked externally.

- If the problem (once the system has been switched off and

back on) persists, contact customer assistance.

E089

- Wrong Wiring

Yellow LED

Incorrect grid wiring connection on Stand Alone:

The error occurs if the grid cables have been incor-

rectly connected to the Stand Alone output.

• Check that the cables on the Stand Alone output have been

installed correctly.

Содержание PVS-50-TL












































































































































































Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды

Fimer PVS-50-TL, Руководство по эксплуатации продукта

Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды