Fimer PVS-50-TL Скачать руководство пользователя страница 106

Страница: 106 / 171

106

000876AG-F

7 - Operation

LED behaviour

The LEDs on the front panel may behave in different ways depending on

the inverter’s operational status.

All possible LED activation combinations are shown in the following ta-

ble. In particular, each LED could behave in one of the following ways:

= LED on

= LED flashing slow (2 seconds on / 2 seconds off)

= LED flashing fast (0.2 seconds on / 0.2 seconds off)

= LED off

= Any one of the conditions described above

LED status

Operating state

green:

yellow:

red:

Firmware programming

The inverter firmware is being programmed

green:

yellow:

red:

Night mode (inverter automatically switches off)

The inverter is in night time switch-off mode (

input voltage less than 70% of the set start-up

voltage).

green:

yellow:

red:

Inverter initialization

This is a transitional state due to verification of the operating conditions. During this stage the

inverter checks that the conditions for connecting to the grid are met.

green:

yellow:

red:

The inverter is connected and is feeding power into the grid

Normal operation. During this stage, the inverter automatically tracks and analyses the pho-

tovoltaic generator's maximum power point (MPP).

green:

yellow:

red:

Disconnection from the grid

Indicates lack of grid voltage. This condition does not allow the inverter to connect to the grid

(the inverter display shows the message "Missing Grid").

green:

yellow:

red:

Warning indication: (W message codes) or Error: (E message codes)

- Indicates that the inverter control system has detected a

warning (W) or error (E). It is possible

to identify the type of problem generated with the Aurora Manager LITE software (see the

alarm

messages).

green:

yellow:

red:

Temperature protection trip

Indicates that the trip relating to internal temperatures (insufficient or excessive temperature)

may have been activated

green:

yellow:

red:

Anomaly in the insulation system of the photovoltaic generator

Indicates that a leakage to earth from the

PV generator has been detected, causing the in

verter to disconnect from the grid.

Содержание PVS-50-TL












































































































































































Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды

Fimer PVS-50-TL, Руководство по эксплуатации продукта

Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды