Fimer PVS-50-TL Скачать руководство пользователя страница 10

Страница: 10 / 171

000006HG-F

1 - Introduction and general information

Symbols and signs

In the manual and/or in some cases on the equipment, the danger or

hazard zones are indicated with signs, labels, symbols or icons.

Symbol

Description

Indicates that it is mandatory to consult the manual or original document,

which must be available for future use and must not be damaged in any

way.

General warning

- Important safety information. Indicates operations or

situations in which staff must be very careful.

Dangerous Voltage

- Indicates operations or situations in which staff

must be very careful with regard to dangerous voltage levels.

Hot parts

- Indicates a risk arising from the presence of hot zones or

zones with parts at high temperatures (risk of burns).

Risk of explosion

Risk of injury due to the weight of the equipment. Take care during lifting

and transport

Indicates that the area in question must not be accessed or that the ope-

ration described must not be carried out.

Keep out of the reach of children

Indicates that smoking and the use of naked flames is prohibited.

Indicates that it is mandatory to carry out the described operations using

theclothing and/or personal protective equipment provided by the em-

ployer.

WEEE logo. Indicates that the product is to be disposed of according to

current legislation regarding the disposal of electronic components.

IPXX

Indicates the protection rating of the equipment according to IEC 70-1

(EN 60529 June 1997) standard.

Point of connection for grounding protection.

Indicates the permitted temperature range

Содержание PVS-50-TL












































































































































































Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды

Fimer PVS-50-TL, Руководство по эксплуатации продукта

Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды