Fimer PVS-50-TL Скачать руководство пользователя страница 97

Страница: 97 / 171

000875BG-F

7 - Operation

After the commissioning via FIMER Installer for Solar Inverters APP

is completed, the inverter changes the behaviour of the “Power” and

“Alarm” LEDs

, in relation of the input voltage value:

Input voltage

LED Status

Description

Vin < Vstart

Power = Flashing

Alarm = OFF

The input voltage is not sufficient to enable connection to

the grid.

Vin > Vstart

Power = Flashing

Alarm = ON

The input voltage is sufficient to enable connection to the

grid: the inverter waits for the grid voltage to be present to

make the connection to the grid.

The inverter is powered SOLELY by the voltage generated by the photovoltaic generator: the

presence of grid voltage alone is NOT SUFFICIENT for the inverter to switch on.

• When the input voltage is sufficient to allow the connection to the grid,

close the AC switch downstream of the inverter thus applying the grid

voltage to the inverter: the inverter checks the grid voltage, measures the

isolation resistance of the photovoltaic field with respect to ground and

performs other auto-diagnostic checks. During the preliminary checks on

the parallel connection with the grid, the “Power” LED keeps flashing,

the “Alarm” and “GFI” LEDs are OFF.

• The inverter ONLY creates a parallel connection with the grid if the grid

and isolation resistance parameters fall within the ranges foreseen by

current regulations.

• If the outcome of the preliminary checks on the grid parallel is positive,

the inverter connects to the grid and starts to export power to the grid.

The “Power” LED remains fixed on while the “Alarm” and “GFI” LEDs are

OFF.

To address any problems that may occur during the initial stages of operation of the system

and to ensure the inverter remains fully functional, you are advised to check for any firmware

updates in the download area of the website www.fimer.com or at https://registration.solar.

fimer.com (instructions for registering on the website and updating the firmware are given in

this manual).

Содержание PVS-50-TL












































































































































































Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды

Fimer PVS-50-TL, Руководство по эксплуатации продукта

Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды