Fimer PVS-50-TL Скачать руководство пользователя страница 113

Страница: 113 / 171

113

000877BG-F

7 - Operation

SETTING section

In the

SETUP

section it’s possible to access the following sub-menus:

• AC output Rating (Only visible with Admin Plus privileges)

• AC Settings (Only visible with Admin Plus privileges)

• Active Power Control (Only visible with Admin Plus privileges)

• DC Settings

• Digital Inputs

• Frequency Control: P(f) (Only visible with Admin Plus privileges)

• Ramp Control (Only visible with Admin Plus privileges)

• Reactive Power Control (Only visible with Admin Plus privileges)

AC output Rating (Only visible and editable with Admin

Plus privileges)

In the

AC output Rating

sub-menu you can config the output power

limitation by changing the Maximum AC output power and the maxi-

mum apparent output power parameters.

Do not change these parameters if not requested by the grid operator.

AC Settings (Only visible and editable with Admin Plus

privileges)

In the

AC Settings

sub-menu you can setup the parameter related to

the Output AC side:

Changing the above-mentioned parameters may prevent disconnection from the grid if the

new values exceed those given in the standards of the country of installation. If these parame-

ters are changed to values outside the standard range, an interface protection must be instal-

led external to the inverter in accordance with the requirements of the country of installation.

1. Grid Connection

By editing these settings it’s possible to change the grid connection

thresholds parameters to which the inverter have to connect to the grid

2. Grid Prote VRT/FRT

By editing these settings it’s possible to enable/disable and change the

grid protection intervention thresholds parameters. In addition it is pos-

sible to change voltage ride thorough (HVRT, LVRT) and frequency ride

thorough (HFRT, LFRT) settings.

Содержание PVS-50-TL












































































































































































Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды

Fimer PVS-50-TL, Руководство по эксплуатации продукта

Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды