Fimer PVS-50-TL Скачать руководство пользователя страница 70

Страница: 70 / 171

000870BG-F

5 - Installation

Input connection to PV generator (DC side)

After having carried out preliminary checks and therefore having verified

that there are no problems in the photovoltaic system, and the channel

configuration has been selected (parallel or independent) you may con

nect the inputs to the inverter.

According to the system configuration, check the correct setting of the channels to indepen

dent or in parallel mode. An incorrect setting of the input channels can lead to loss of energy

production.

Comply with the maximum input current relating to the quick-fit connectors as indicated in the

technical data.

Polarity inversion can cause serious damage. Check polarity before connecting each string!

When the photovoltaic panels are exposed to sunlight they provide continuous DC voltage

to the inverter.

To avoid risks of electrical shock,

all wiring operations must be carried out

with the DC disconnect switch (internal or external to the inverter) OFF.

Caution! The inverters referred to in this document are TRANSFORMERLESS. This type

requires the use of insulated photovoltaic panels (IEC61730 Class A Rating) and the need to

keep the photovoltaic generator floating with respect to ground: no terminal of the generator

must be connected to ground.

The DC side connections are different according to the version used:

- the

Standard / -S

models use cable glands

- the

-SX / -SX2

models use quick fit connectors (one for each pole of each

string).

On the

Standard / -S versions, the connection in parallel of the strings ( array composition)

must take place upstream of the input in the inverter and must be made by technicians during

installation.

The -

SX / -SX2

versions accept a direct single strings connection with

con-

nectors which are located on the outside of the mechanics.

To avoid risks of electrical shock,, all the connect operations must be carried out with the DC

disconnect switch

and the external AC disconnect switch open.

Содержание PVS-50-TL












































































































































































Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды

Fimer PVS-50-TL, Руководство по эксплуатации продукта

Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды