Fimer PVS-50-TL Скачать руководство пользователя страница 128

Страница: 128 / 171

128

000877BG-F

7 - Operation

For the configurable relay operating mode “Alarm Conf.”, the following considerations are

valid:
If the alarm condition is persistent, the alarm contact cyclically switches from its resting state

to its activated state.
In the presence of W002 signalling (Input UV – input voltage below the limit of operation),

the alarm contact switches to then reset itself at the end of the alarm signal. This means that

during the reduced input voltage (display message “Waiting Sun”) the alarm contact remains

in its resting position.
In the presence of W003, W004, W005, W006, W007 signalling, the alarm contact switches

to then reset itself at the end of the alarm signal. This means that during the absence of grid

voltage (display message “Missing Grid”) the alarm contact remains in its resting position.

• Alarm-Contact (crepuscolar):

The relay is activated (status: switched) as soon as the inverter input

voltage exceeds the activation voltage set.

The relay switch to rest position when the input voltage drops below 70%

of the activation voltage set.

This mode is useful for disconnecting any output transformers that could

have unnecessary consumption during the night.

• Alarm-Contact (alarm ALL - latch):

The relay is activated (status: switched) whenever an error (code Exxx)

or a warning (code Wxxx) is present. When the inverter returns to the

normal operating state and reconnects with the grid, the contact returns

to its position of rest.

Selectable alarms for which the relay is activated

E001

E002

E003

E004

E005

E006

E007

E010

E011

E013

E014

E015

E017

E018

E019

E020

E021

E022

E023

E025

E029

E031

E032

E033

E034

E036

E037

E053

E055

E075

E077

E078

E079

E080

E084

W002

W004

W005

W006

W007

W011

W015

W017

W046

W047

W048

If the alarm condition is persistent, the relay will remain activated (sta-

tus:switched)

Vin > Vstart

Vin < Vstart

GRID RECONNECTION

t=based on Country Standard

Vin

IS STILL LESS THAN

Vstart

Yes

N.C.

N.O.

N.C.

N.O.

N.C.

N.O.

Relay State:

Idle

Relay State: Switched

Relay State:

Idle

INVERTER RUN

ERROR OCCURENCY

ERROR MESSAGE

t=15s

GRID RECONNECTION

t=based on Country Standard

ERROR

STILL

PRESENT

Yes

N.C.

N.O.

N.C.

N.O.

Relay State:

Idle

Relay State: Switched

N.C.

N.O.

Relay State: Switched

Содержание PVS-50-TL












































































































































































Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды

Fimer PVS-50-TL, Руководство по эксплуатации продукта

Результаты поиска

Содержание PVS-50-TL

Отзывы:

Похожие инструкции для PVS-50-TL

Бренды по названию

Популярные бренды